AMLinux/OpenELEC (amlogic s802/805)

[bobones]

Does anyone know how to get acestream p2p to work with these ports?

[csgabe]

Yes, I flashed OpenELEC-Amlogic.TV110.arm-devel-20150116225823-r20304-gfabfc2f-update.zip wit MD5 checksum:1c86d1264e29f73c2ef0b745d19675b3
Yes, this uboot works ok(I think it's same as from AP6210 S805TV110 2014.09.26.zip, last firmware from usb-ect website)

[kerber]

@All
for BT
killall -9 brcm_patchram_plus
echo 0 > /sys/class/rfkill/rfkill0/state
echo 1 > /sys/class/rfkill/rfkill0/state; /usr/bin/brcm_patchram_plus --patchram /lib/firmware/brcm/BCM20702.hcd --baudrate 3000000 --enable_hci --use_baudrate_for_download --tosleep 15000 --no2bytes /dev/ttyS2 (if you have ttyS2) ttyS1 (if you have ttyS1)

@bobones send me right u-boot please.
@csgabe

AP6210, uart port should be /dev/ttyS2

My box have ap6210 and have ttyS1

[csgabe]

I wanted to say that my TV110 has AP6210 wifi, and bt_vendor.conf contains a line with UartPort = /dev/ttyS2.

[Amhub]

Сообщение от kerber

@All
for BT
killall -9 brcm_patchram_plus
echo 0 > /sys/class/rfkill/rfkill0/state
echo 1 > /sys/class/rfkill/rfkill0/state; /usr/bin/brcm_patchram_plus --patchram /lib/firmware/brcm/BCM20702.hcd --baudrate 3000000 --enable_hci --use_baudrate_for_download --tosleep 15000 --no2bytes /dev/ttyS2 (if you have ttyS2) ttyS1 (if you have ttyS1)

@bobones send me right u-boot please.
@csgabe

My box have ap6210 and have ttyS1

I tried with ttyS1, but not working.
My box have ap6330.

ls /dev/ttyS*
/dev/ttyS0
/dev/ttyS1
/dev/ttyS4

[csgabe]

@Amhub
Does it display "Done setting line discpline". If it hangs after that then try removing --enable_hci option, add -d to /usr/bin/brcm_patchram_plus to see some output and run again(maybe restart before). Then run these commands:

hciattach /dev/ttyS1 any
hcitool dev
hciconfig -a
hcitool scan

See issue described here:
http://code.google.com/p/broadcom-bl...es/detail?id=3
What does dmesg output?

[Amhub]

No, there is no message as "Done setting line discpline".
I tried with with and without "--enable_hci option", every time freezes console window.

After reboot:

/$ hciattach /dev/ttyS1 any
Device setup complete

/$ hcitool dev
Devices:

/$ hciconfig -a
hci0:	Type: BR/EDR  Bus: UART
	BD Address: 00:00:00:00:00:00  ACL MTU: 0:0  SCO MTU: 0:0
	DOWN 
	RX bytes:0 acl:0 sco:0 events:0 errors:0
	TX bytes:12 acl:0 sco:0 commands:3 errors:0
	Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
	Packet type: DM1 DH1 HV1 
	Link policy: 
	Link mode: SLAVE ACCEPT 

/$ hcitool scan
Device is not available: No such device

[FANTOM]

on S82 (AP6210) with this fw OpenELEC-Amlogic.S82.arm-devel-20150118172337-r20312-g120caa9-update.zip
bluetooth working.. devices seeking...
but I do not know how I can apply it

[ChaosKing]

OpenELEC-Amlogic.S82.arm-devel-20150118172337-r20312-g120caa9

Tested on tronsmart s89 -> No video in hevc files (screen is black, sound ok)

[kerber]

Yes, S802 don't support HEVC, only S805 and S812